牡蛎对浮游植物群落下行控制作用的围隔实验研究     

王兆慧  张光涛 《海洋科学》2020,44(9):47-53

牡蛎的滤食作用不但能控制浮游植物丰度，还能通过摄食选择性影响群落结构。通过在较高营养水体的围隔实验表明，牡蛎养殖在持续磷限制条件下，促使浮游植物群落由甲藻向小型硅藻优势转变。实验结束时对照组中浮游植物群落由扁压原甲藻主导，占总丰度的77%；而牡蛎养殖组新月柱鞘藻丰度占比达到93%。牡蛎养殖组中，甲藻去除速率随养殖密度增长，但是硅藻最终丰度在高密度牡蛎组最高。研究结果说明大量的贝类养殖能够提升小型链状硅藻的优势度，增加此类赤潮发生风险。  相似文献   

五圆柱体结构群绕流特性及互扰效应研究     

涂佳黄  张志豪  曹波  肖毅凡  梁经群 《海洋工程》2020,38(1):101-110

基于Fluent流体计算平台,运用大涡模拟方法对亚临界雷诺数Re=3900下“X”形排列五圆柱体结构群三维绕流特性进行研究,主要分析来流攻角α与间距比L/D两个关键参数对五圆柱体结构群的尾流区三维涡结构演化与流体力系数的影响,并揭示其内在流动互扰机理。研究表明:来流攻角和间距比的变化对五圆柱体结构群流动控制及互扰效应的影响显著。在小间距比工况下,观察到柱体群间隙区域内流体高速流动的现象,导致五圆柱体之间的互扰作用十分强烈。间隙流对中间圆柱体和下游圆柱体有较强的冲击作用,对其表面的流体力分布特性有显著的影响。另外,大间距比工况下,当α=0°与L/D≥5.0工况时,柱体群尾流效应强于其间隙流效应。当α=22.5°与L/D=7.0时,位于下游与中间处的圆柱体流体绕流特性存在较大差异。而当α=45°与L/D≥6.0时,位于上游与中间处的圆柱体尾流区均会产生正负交替的漩涡结构。  相似文献   

Application of flocculation combined with vacuum preloading to reduce river-dredged sludge     

Feiyu Liu  Wenqing Wu  Jun Wang  Jun Hai  Yuanqiang Cai 《Marine Georesources & Geotechnology》2020,38(2):164-173

Abstract

To achieve the rapid dewatering of dredged sludge, the flocculation–vacuum-preloading method was tested indoors. In this study, the optimal mixing ratio of six flocculants was determined through the settling column test, and then the proposed method was tested. The water drainage and settlement were monitored during the test, while the soil moisture content and shear strength were measured after the test. The results show that all the flocculants had an optimal mixing ratio, and the addition of 0.8% FeCl₃ or 0.08% anionic polyacrylamide (APAM) in the sludge can better accelerate solid–liquid separation of the sludge. After the test, the water content in the sludge decreased from 140% to 60%. Compared with general vacuum preloading, the use of the proposed method increased the water drainage by 46.5% and 56.8% and decreased the soil volumes by 60.5% and 82.4% for FeCl₃ and APAM, respectively. Moreover, the corresponding shear strength was increased from 10 to 14 and 17?kPa. In addition, the use of APAM increased the solidification rate of heavy metals in the sludge to more than 80%, effectively inhibiting the migration of heavy metals.  相似文献   

利用接收函数方法研究中国东北东南部地区不同构造体的地壳特征   总被引：3，自引：0，他引：3       下载免费PDF全文

李天觉  陈棋福 《地球物理学报》2019,62(8):2899-2917

基于我们布设的探测深俯冲的中国东北地震台阵NECsaids台阵和固定地震台长时段的观测记录及NECESSArray流动台阵共计152个台站数据提取得到的33752条P波接收函数，采用H-κ叠加分析和共转换点（CCP）叠加成像等方法进行统一分析处理，并汇集他人接收函数研究结果得到中国东北东南部地区迄今为止最高分辨率的地壳厚度和平均波速比分布图像.对中国东北东南部地区不同构造体的地壳特征综合分析研究表明：研究区不同陆块的地壳属性存在明显差别，张广才岭地块中南部的地壳厚度和波速比与华北克拉通东北缘相当，地壳厚度同地表地形之间显示有明显的正相关关系；松辽地块东南缘地壳最薄、波速比最高，地壳厚度同壳内波速比之间显示出明显的负相关关系；兴凯地块西部地区的地壳结构表现为稍厚的地壳厚度和研究区内最低的壳内波速比，其地壳厚度同壳内波速比之间亦显示出明显的负相关关系；佳木斯地块西南缘在具有"正常"的壳内波速比同时地壳最厚.研究区内的郯庐断裂带北延段在切穿其下Moho面的同时表现出南北分段的特征：北段（44.4°N—47°N）两分支之下的Moho面整体下凹，而南段（41.5°N—43.3°N）两分支之下的Moho面则整体上隆.长白山天池火山下方表现为Moho面下凹沉落及高壳内波速比特征，推测其壳内岩浆囊很可能存在于火山口东北隅至少10 km的范围内.  相似文献   

九寨沟7.0级地震房屋震害现场调查及其破坏特征   总被引：2，自引：0，他引：2       下载免费PDF全文

张令心  朱柏洁  陶正如  陈相兆 《地震工程学报》2019,41(4):1053-1059

2017年8月8日四川省阿坝州九寨沟县发生7.0级地震,震源深度20 km,造成大量房屋不同程度的破坏,引发地质灾害。针对Ⅷ、Ⅸ区的337栋不同结构类型的房屋进行了震害特征分析,给出震害矩阵,揭示各类结构房屋的破坏机理。经过统计,所调查的房屋中3.3%的建筑保持完好,19.9%的建筑发生轻微破坏,51.3%的建筑发生中等破坏,21.1%的建筑发生严重破坏,4.5%的建筑发生毁坏。经过调查,钢筋混凝土框架结构、大跨度空间结构、钢框架结构以及采用木板作为填充墙的穿斗式木构架房屋在本次地震中表现良好。分析表明,经过合理的抗震设计,基本达到了中震可修的抗震设防目标,极大程度地保护了人们的生命及财产安全。  相似文献   

华北克拉通西部块体北缘及邻区地壳厚度与泊松比分布特征     

杨彦明  陈婧  熊峰  张云  马援  贾昕晔  贾彦杰 《地震》2019,39(2):97-109

收集了2010—2011年华北克拉通西部块体北缘及邻区布设的36个流动地震台和2009—2016年内蒙古自治区数字地震台网17个宽频带固定地震台站的远震事件波形数据, 采用接收函数H-κ算法分析获得了53个基岩台站下方的地壳厚度和泊松比结果。 此外, 结合已有的81个台站的研究成果, 给出华北克拉通西部块体北缘及邻区地壳厚度与泊松比分布特征。 综合分析认为, 研究区地壳厚度在整体上呈现自东向西渐变的特征, 最厚的地方出现在华北克拉通西端的阿拉善地块(～48.7±3.0 km)。 研究区平均泊松比为0.27, 泊松比高值异常出现在河套断陷带, 意味着可能具有较高的地壳温度或者存在壳内部分熔融。 研究区内不同构造单元呈现出显著的地壳厚度和泊松比分布特征的差异性, 意味着在华北克拉通构造演化过程中, 不同地区经历了不同的地壳改造过程。  相似文献   

唐山震区上地壳平均波速比分析     

信世民  郭学增  刘静  张蕾  李瑞卿 《地震地磁观测与研究》2019,40(3):15-20

收集河北地震台网记录的唐山震区2012-2016年M_L ≥ 1.0地震，选取震源深度5-10 km、波形信噪比较高的波形数据，拾取直达P波、S波震相到时，利用和达法计算平均波速比，并分析研究区平均波速比水平分布特征与时变特征，结果表明：唐山震区上地壳平均波速比约为1.71，且水平分布呈区域化特征，反映了研究区复杂的地壳结构。研究区内3次M_L ≥ 4.0地震前，波速比曲线均呈较显著的下降-低值-回升形态，表明该区平均波速比变化可能具有一定地球物理异常特征。  相似文献   

Establishment and application of an intelligent treating method for oil spill identification     

TAN Liju  ZHAO Ruxiang  YIN Xiaonan  ZHANG Haijiang  WANG Jiangtao 《海洋学报(英文版)》2018,37(11):116-122

In the identifying process of an oil spill accident, manual integral and artificial visual comparison are commonly used at present to determine the oil spill sources, these methods are time-consuming and easily affected by human factors. Therefore, it is difficult to achieve the purpose of rapid identification of an oil spill accident. In this paper, an intelligent method of automatic recognition, integration and calculation of diagnostic ratio of Gas Chromatography-Mass Spectrometer (GC/MS) spectrum are established. Firstly, four hundreds of samples collected around the world were analyzed using a standard method and Retention time locking technology (RTL) was applied to reduce the change of retention time of GC/MS spectrum. Secondly, the automatic identification, integration of n-alkanes, biomarker compounds, polycyclic aromatic hydrocarbons and calculation of the diagnostic ratios were realized by MATLAB software. Finally, a database of oil fingerprints were established and applied successfully in a spill oil accident. Based on the new method and database, we could acquire the diagnostic ratios of an oil sample and find out the suspected oil within a few minutes. This method and database can improve the efficiency in spilled oil identification.  相似文献   

Global Statistical Assessment and Cross-Calibration with Jason-2 for Reprocessed HY-2 A Altimeter Data     

Maofei Jiang  Ke Xu  Yalong Liu 《Marine Geodesy》2018,41(3):289-312

HY-2 A (Haiyang-2 A) satellite was launched on August 16, 2011 and radar altimeter is one of its main payloads. We reprocessed two years of HY-2 A altimeter sensor geophysical dataset records (SGDR) data. This paper presents the main results in terms of reprocessed HY-2 A altimeter data quality: verification of data availability and validity, monitoring several relevant altimeter parameters, and assessment of the HY-2 A altimeter system performances. A cross-calibration analysis of reprocessed HY-2 A altimeter data with Jason-2 was conducted. The reprocessed HY-2 A altimeter data show good quality and have a low level of noise with respect to Jason-2. The same geophysical correction methods were used to calculate the sea surface height (SSH) for the two missions. The mean standard deviations of the crossover differences for HY-2 A and Jason-2 are 5.24 cm and 5.34 cm, respectively. The mean standard deviation of the crossover differences between HY-2 A and Jason-2 is 5.37 cm. These show that HY-2 A can provide SSH measurements at almost the same level of accuracy as Jason-2. The relative SSH bias between HY-2 A and Jason-2 due to the Ultra Stable Oscillator (USO) drift is obviously observed, and it can affect the calculation of mean sea level and should be further studied and corrected.  相似文献   

不同固有频率比条件下圆柱双自由度涡激振动特性的数值研究   总被引：1，自引：1，他引：0  

翟云贺  康庄  宋儒鑫  孙丽萍 《海洋工程》2018,36(4):50-59

采用RANS方法,结合SST k-ω湍流模型,对不同顺流向与横顺流向固有频率的比值(即固有频率比,fnx/fny)条件下低质量比圆柱体的双自由度涡激振动进行了二维数值模拟。圆柱体的质量比为2.6,雷诺数范围为2 500~18 750,相应的约化速度范围为2~15,包括了经典试验中出现的整个锁定范围。通过研究发现,固有频率比是影响振动特性的重要参数,随着固有频率比的增加,响应幅值逐渐降低且向更高的约化速度偏移;在低约化速度范围内,固有频率比对顺流向和横流向振动之间的相位差以及升力频率有较大影响,从而得到各种不同偏向的8字形轨迹;最后对不同固有频率比条件下的尾涡模式进行了讨论,给出了对应不同约化速度时的尾涡模式。  相似文献